Riptide
11-05-2009, 23:31
Mods please delete my previous 2 posts - I combined them in here.
Cleaning out the drawers - need to finish my Shuttle PC build.
First up guns.
TM P90 RDS, lower stock painted textured and khaki. Barely fielded - only held around.
http://i8.photobucket.com/albums/a1/aznriptide859/Airsoft/IMG_0265.jpg
http://i8.photobucket.com/albums/a1/aznriptide859/Airsoft/IMG_0266.jpg
http://i8.photobucket.com/albums/a1/aznriptide859/Airsoft/IMG_0260-1.jpg
http://i8.photobucket.com/albums/a1/aznriptide859/Airsoft/IMG_0261-1.jpg
Added a pressure switch on bottom (not wired) and cut hole out in front for a Laserex module - never finished it though.
Comes with:
1 x Madbull H-Nub Upgrade (Installed)
3 x 8.4v Batteries
1 x 300rnd hicap
1 x homemade rear sling mount
Asking $190 OBO.
Can also add:
PS90 Outer barrel +$30
Front FH Sling mount +$10
First Factory P90 RIS Mount +$40
As for the parts:
KA PS90 Outer Barrel. $35
http://i8.photobucket.com/albums/a1/aznriptide859/Airsoft/IMG_0272.jpg
Front FH Sling Mount. Screws into behind P90 flash hider. No pic - $10.
First Factory P90 RIS Mount. Replaces RDS upper for a RIS mount - flush fit w/ receiver, good looking IMO. $45 - retails for $55+.
http://i8.photobucket.com/albums/a1/aznriptide859/Airsoft/IMG_0262.jpg
M4 project:
http://i8.photobucket.com/albums/a1/aznriptide859/Airsoft/IMG_0267.jpg
http://i8.photobucket.com/albums/a1/aznriptide859/Airsoft/IMG_0268.jpg
Let's just say it went south - didn't work out as well as I planned.
Externals:
STAR M4 Colt MBK
DBoys Alum Outer Barrel
Oracon/Element Daniel Defense Mk18 RIS II
DYTAC SCAR FH 14mm CCW
ACM Magpul MIAD
ACM Magpul MBUS
Magpul PTS CTR (not MOE crap)
Internals:
Guarder Hopup Unit
Systema Bucking
Element H-Nub (Black)
DBoys 7mm Reinforced GB
Systema Cylinder Head
Systema Cylinder (Type 0)
Guarder Piston Head
Guarder Piston
ICS M120
Element Metal Spring Guide (V2)
Element Flat Gearset
Guarder AR Latch
Systema LR Wiring Harness
Systema Selector Plate
Wired for crane stock setup/buffer tube lipo
Problems:
No faux bolt catch.
No motor included. Can include motor listed below for an extra $10.
STAR MBK is gay - doesn't have a buffer tube mounting like other TM-compatible MBK's. I tried cutting an ICS one, but never got around to it - basically the buffer tube has no point to stay stable. It mounts on, but with heavy use it will get loose. I suggest getting a new MBK or modding the ICS stock adapter (will include w/ purchase).
Total almost $500-700 building cost - asking $325 OBO. WILL NOT SPLIT ANYTHING.
Parts time.
G&P G36E Handguard w/ bipod. No outer barrel. $45.
JG G36C body. Almost no screws, no gas block assembly. $10.
http://i8.photobucket.com/albums/a1/aznriptide859/Airsoft/IMG_0269.jpg
Heavily upgraded G36 gearbox. Used in my MG36, but since it didn't come back in one piece, selling it separately.
http://i8.photobucket.com/albums/a1/aznriptide859/Airsoft/IMG_0270.jpg
Included:
JG G36C base
KA G36C Selector Plate
Guarder LR Wiring Harness
Hurricane Cylinder Head
Hurricane Cylinder (Type 0)
Guarder Piston Head
Guarder Piston
Stock JG M110 Spring
Hurricane V3 Metal Spring Guide
CA HS Gears
CA HS Motor
Should be wired for front, deans. Should reach a pretty good ROF, but haven't checked recently. Asking $100 OBO for the set.
http://i8.photobucket.com/albums/a1/aznriptide859/Airsoft/IMG_0264.jpg
SRC M4 grip w/ motor plate. $10.
ACM 110rnd Fast Loader. $5.
2 x ACM 150rnd Fast Loader. $7.
Shooters Design Loading Nozzle for TM HiCapa/1911 (has TM valve knocker and valve stopper). $15.
UTG Large Foregrip, painted woodland camo. $15.
http://i8.photobucket.com/albums/a1/aznriptide859/Airsoft/IMG_0271.jpg
Guarder 455mm 6.03mm-diameter TBB for AK's and the such. $30.
http://i8.photobucket.com/albums/a1/aznriptide859/Airsoft/IMG_0258.jpg
From left to right:
Pack 1:
Element 200% Torque Up Gearset
JG Piston Head
X-ring
Reinforced AR Latch
$35 shipped
Pack 2:
JG/Dboys Gearset
$15 shipped
Pack 3:
Guarder Sector Gear
Dboys Spur Gear
Guarder Bevel Gear
Element HS Clear Piston
$30 shipped
http://i8.photobucket.com/albums/a1/aznriptide859/Airsoft/IMG_0262.jpg
JG G36C Magwell. $10.
PPA M4 Magwell for G36. Nozzle is broken - mag locks, but won't feed. Use for parts maybe? $5.
TM EG1000 Long motor. Pinion is heavily worn, but it works. $15 - add $10 to M4 package if you want it w/ the M4.
First Factory P90 RIS mount (shown above as well) - $45.
(In Back) DBoys Cylinder head + Dboys Polished Cylinder (Type 1) - $10.
Stock Dboys M100 spring. $5.
http://i8.photobucket.com/albums/a1/aznriptide859/Airsoft/IMG_0274.jpg
M4 Magpuls (black). $5 each, $35 for all.
http://i8.photobucket.com/albums/a1/aznriptide859/Airsoft/IMG_0263.jpg
Dboys Hk416 lower receiver. Markings are all there, but front pin locking section is broken - still locks w/ receiver very sturdily though. $10.
http://i8.photobucket.com/albums/a1/aznriptide859/Airsoft/IMG_0273.jpg
2 AWS Sentry MOSFET's - last gen, but they work. Both have build in 30A resettable fuses, one is heat-shrinked, one is not. $40 for the heat shrinked one, $35 for the non-heat shrinked one.
Paypal accepted only (check/cash if you live in Houston/can arrange pickup). Shipping is NOT included in prices, multiple items = lower shipping cost.
Thanks for looking - please buy!!! :D
Cleaning out the drawers - need to finish my Shuttle PC build.
First up guns.
TM P90 RDS, lower stock painted textured and khaki. Barely fielded - only held around.
http://i8.photobucket.com/albums/a1/aznriptide859/Airsoft/IMG_0265.jpg
http://i8.photobucket.com/albums/a1/aznriptide859/Airsoft/IMG_0266.jpg
http://i8.photobucket.com/albums/a1/aznriptide859/Airsoft/IMG_0260-1.jpg
http://i8.photobucket.com/albums/a1/aznriptide859/Airsoft/IMG_0261-1.jpg
Added a pressure switch on bottom (not wired) and cut hole out in front for a Laserex module - never finished it though.
Comes with:
1 x Madbull H-Nub Upgrade (Installed)
3 x 8.4v Batteries
1 x 300rnd hicap
1 x homemade rear sling mount
Asking $190 OBO.
Can also add:
PS90 Outer barrel +$30
Front FH Sling mount +$10
First Factory P90 RIS Mount +$40
As for the parts:
KA PS90 Outer Barrel. $35
http://i8.photobucket.com/albums/a1/aznriptide859/Airsoft/IMG_0272.jpg
Front FH Sling Mount. Screws into behind P90 flash hider. No pic - $10.
First Factory P90 RIS Mount. Replaces RDS upper for a RIS mount - flush fit w/ receiver, good looking IMO. $45 - retails for $55+.
http://i8.photobucket.com/albums/a1/aznriptide859/Airsoft/IMG_0262.jpg
M4 project:
http://i8.photobucket.com/albums/a1/aznriptide859/Airsoft/IMG_0267.jpg
http://i8.photobucket.com/albums/a1/aznriptide859/Airsoft/IMG_0268.jpg
Let's just say it went south - didn't work out as well as I planned.
Externals:
STAR M4 Colt MBK
DBoys Alum Outer Barrel
Oracon/Element Daniel Defense Mk18 RIS II
DYTAC SCAR FH 14mm CCW
ACM Magpul MIAD
ACM Magpul MBUS
Magpul PTS CTR (not MOE crap)
Internals:
Guarder Hopup Unit
Systema Bucking
Element H-Nub (Black)
DBoys 7mm Reinforced GB
Systema Cylinder Head
Systema Cylinder (Type 0)
Guarder Piston Head
Guarder Piston
ICS M120
Element Metal Spring Guide (V2)
Element Flat Gearset
Guarder AR Latch
Systema LR Wiring Harness
Systema Selector Plate
Wired for crane stock setup/buffer tube lipo
Problems:
No faux bolt catch.
No motor included. Can include motor listed below for an extra $10.
STAR MBK is gay - doesn't have a buffer tube mounting like other TM-compatible MBK's. I tried cutting an ICS one, but never got around to it - basically the buffer tube has no point to stay stable. It mounts on, but with heavy use it will get loose. I suggest getting a new MBK or modding the ICS stock adapter (will include w/ purchase).
Total almost $500-700 building cost - asking $325 OBO. WILL NOT SPLIT ANYTHING.
Parts time.
G&P G36E Handguard w/ bipod. No outer barrel. $45.
JG G36C body. Almost no screws, no gas block assembly. $10.
http://i8.photobucket.com/albums/a1/aznriptide859/Airsoft/IMG_0269.jpg
Heavily upgraded G36 gearbox. Used in my MG36, but since it didn't come back in one piece, selling it separately.
http://i8.photobucket.com/albums/a1/aznriptide859/Airsoft/IMG_0270.jpg
Included:
JG G36C base
KA G36C Selector Plate
Guarder LR Wiring Harness
Hurricane Cylinder Head
Hurricane Cylinder (Type 0)
Guarder Piston Head
Guarder Piston
Stock JG M110 Spring
Hurricane V3 Metal Spring Guide
CA HS Gears
CA HS Motor
Should be wired for front, deans. Should reach a pretty good ROF, but haven't checked recently. Asking $100 OBO for the set.
http://i8.photobucket.com/albums/a1/aznriptide859/Airsoft/IMG_0264.jpg
SRC M4 grip w/ motor plate. $10.
ACM 110rnd Fast Loader. $5.
2 x ACM 150rnd Fast Loader. $7.
Shooters Design Loading Nozzle for TM HiCapa/1911 (has TM valve knocker and valve stopper). $15.
UTG Large Foregrip, painted woodland camo. $15.
http://i8.photobucket.com/albums/a1/aznriptide859/Airsoft/IMG_0271.jpg
Guarder 455mm 6.03mm-diameter TBB for AK's and the such. $30.
http://i8.photobucket.com/albums/a1/aznriptide859/Airsoft/IMG_0258.jpg
From left to right:
Pack 1:
Element 200% Torque Up Gearset
JG Piston Head
X-ring
Reinforced AR Latch
$35 shipped
Pack 2:
JG/Dboys Gearset
$15 shipped
Pack 3:
Guarder Sector Gear
Dboys Spur Gear
Guarder Bevel Gear
Element HS Clear Piston
$30 shipped
http://i8.photobucket.com/albums/a1/aznriptide859/Airsoft/IMG_0262.jpg
JG G36C Magwell. $10.
PPA M4 Magwell for G36. Nozzle is broken - mag locks, but won't feed. Use for parts maybe? $5.
TM EG1000 Long motor. Pinion is heavily worn, but it works. $15 - add $10 to M4 package if you want it w/ the M4.
First Factory P90 RIS mount (shown above as well) - $45.
(In Back) DBoys Cylinder head + Dboys Polished Cylinder (Type 1) - $10.
Stock Dboys M100 spring. $5.
http://i8.photobucket.com/albums/a1/aznriptide859/Airsoft/IMG_0274.jpg
M4 Magpuls (black). $5 each, $35 for all.
http://i8.photobucket.com/albums/a1/aznriptide859/Airsoft/IMG_0263.jpg
Dboys Hk416 lower receiver. Markings are all there, but front pin locking section is broken - still locks w/ receiver very sturdily though. $10.
http://i8.photobucket.com/albums/a1/aznriptide859/Airsoft/IMG_0273.jpg
2 AWS Sentry MOSFET's - last gen, but they work. Both have build in 30A resettable fuses, one is heat-shrinked, one is not. $40 for the heat shrinked one, $35 for the non-heat shrinked one.
Paypal accepted only (check/cash if you live in Houston/can arrange pickup). Shipping is NOT included in prices, multiple items = lower shipping cost.
Thanks for looking - please buy!!! :D